Airbrush CoCo BROW - Black

Complete Control Over Application

With the ability to adjust the paint mixture, the airbrush allows for a variety of effects—from delicate and subtle to intense. This beauty tool is suitable for both experienced professionals and those new to the airbrush method.

Elevate your eyebrow styling standards with our modern airbrush and enjoy the perfection and satisfaction of your clients every day.

Directions for use:

1. Charge the airbrush for at least 2 hours. Assemble the airbrush, cup, and air compressor according to the instructions included in the kit.

2. The mixing ratio for CoCo Lashes hybrid dyes is always 2:1. Remember to use only liquid developer for the Airbrush technique!

3. To prepare the eyebrow dye, pour 12 drops of CoCo Brow Stain and 6 drops of liquid developer into a plastic container (note: always pour the developer first, then the color).

4. Close the container with the lid.

5. Turn on the device. Press once to set position 1, press twice to set position 2.

6. Place your finger or a cotton pad over the nozzle and press the trigger; the device will now turn on.

7. Slowly pull the trigger back to start mixing the dye with the bubbling method.

8. The stain will start to bubble slightly. After about 10 seconds, the dye will be well mixed.

9. Press the trigger, slowly pulling it back to start spraying.

10. First, spray a cotton pad to check if the dye has the right consistency and color.

11. After each use, clean the airbrush using the bubbling method.

Cleaning the Airbrush

Regular and thorough cleaning of the airbrush is essential to ensure the quality of work and extend the device's lifespan.

How often to clean the airbrush?

The airbrush should be cleaned after each use to prevent leftover dye from affecting the quality of future work.

Cleaning after each session - bubbling method:

1. Remove excess dye from the plastic container using a cotton pad.

2. Fill the container halfway with water, then spray it into a bowl or onto a piece of paper towel to remove leftover dye.

3. Remove the container, wash it under running water, and then place it back on the gun.

4. Fill the container with warm water.

5. Place your finger over the nozzle.

6. Press the trigger and slowly pull it back. The water will start to bubble.

7. Let the water bubble for 10 seconds, then pour it out.

8. Repeat this process two more times.

9. Fill the container with clean water, remove your finger from the nozzle, and spray the water into a bowl or sink.

10. Spray until no water comes out of the nozzle.

Deep cleaning the airbrush at the end of the workday:

1. Rinse the airbrush using the bubbling method described above.

2. Remove the plastic container, needle cover, and nozzle cap. These are the two rings that form the nozzle.

3. Place these parts in a bowl of water.

4. Use the brushes from the kit to clean the dye container hole.

5. Carefully remove and clean the needle by unscrewing the airbrush neck, preferably with a cotton swab soaked in alcohol.

6. Take the container, needle cover, and nozzle cap out of the bowl. Clean them thoroughly with the provided brush. Dry all parts with a paper towel.

7. Now you can reassemble everything, and your airbrush will be ready for the next day.

Kit Contains:

* 1 x Airbrush

* 1 x Spare Nozzle

* 1 x Eyedropper

* 5 x Cleaning Brushes

* 5 x Cleaning Needles

* 1 x Air Compressor

* 1 x Metal Cup (5ml)

* 2 x Plastic Cups (15 & 35ml)

* 1 x USB Charging Cable

* 1 x Instruction Manual

Specifications:

Battery Working Time: 50-75 minutes

Air Pressure Modes: 23, 28 & 32psi

Charging Time: 1.5-2.5 hours

Atomisation Flow: 0.012mm (approx)

Nozzle Size: 0.3mm

Charging Method: Standard USB Charging

Battery Capacity: 1400 mA

Power: 8W

Input Voltage: 5V/1A

Liquid Cup Capacity: 5, 15 & 35ml